單級入軌

單級入軌（英語：Single-stage-to-orbit，縮寫：SSTO）是從地面發射一個航天器直接入軌，不拋棄燃料箱、發動機或其他主要部件，屬於可重複使用發射系統的一種。目前，尚沒有從地球發射的單級入軌系統被製成，實際使用的都是一次性使用運載系統多級火箭。

冒險之星是一個單級入軌項目提案。

理論上，使用化學能驅動的火箭發動機能實現從地球的單級入軌。但挑戰在於：軌道速度要超過7,400米每秒（27,000公里每小時；17,000英里每小時）、起飛階段克服地球稠密大氣層的阻力，再入階段的熱防護，綜合成本的競爭力。

在其他質量較小且沒有大氣層的天體表面發射單級入軌航天器是現實可行的，如火星、月球。阿波羅登月的登月艙、蘇聯的幾艘無人自動登月返回的月球號系列探測器等都實現了月面的單級入軌。

歷史

早期概念

ROMBUS概念圖

二十世紀中葉前，對太空旅行的研究還很少。1960年代，這種工藝的一些早期概念設計開始湧現。

單級入軌最早的概念之一是道格拉斯飛行器公司工程師Philip Bono提出的一次性的一級軌道太空卡車（One stage Orbital Space Truck）。另也提出了一個名為「ROOST」的可重用版本。

已隱藏部分未翻譯內容，歡迎參與翻譯。

Another early SSTO concept was a reusable launch vehicle named NEXUS which was proposed by Krafft Arnold Ehricke in the early 1960s. It was one of the largest spacecraft ever conceptualized with a diameter of over 50 metres and the capability to lift up to 2000 short tons into Earth orbit, intended for missions to further out locations in the solar system such as Mars. The North American Air Augmented VTOVL from 1963 was a similarly large craft which would have used ramjets to decrease the liftoff mass of the vehicle by removing the need for large amounts of liquid oxygen while traveling through the atmosphere.

From 1965, Robert Salked investigated various single stage to orbit winged spaceplane concepts. He proposed a vehicle which would burn hydrocarbon fuel while in the atmosphere and then switch to hydrogen fuel for increasing efficiency once in space.

Further examples of Bono's early concepts (prior to the 1990s) which were never constructed include:

• ROMBUS (Reusable Orbital Module, Booster, and Utility Shuttle), another design from Philip Bono. This was not technically single stage since it dropped some of its initial hydrogen tanks, but it came very close.
• Ithacus, an adapted ROMBUS concept which was designed to carry soldiers and military equipment to other continents via a sub-orbital trajectory.
• Pegasus, another adapted ROMBUS concept designed to carry passengers and payloads long distances in short amounts of time via space.
• SASSTO, another launch vehicle concept.
• Hyperion, yet another Philip Bono concept which used a sled to build up speed before liftoff to save on the amount of fuel which had to be lifted into the air.

Around 1985 the NASP project was intended to launch a scramjet vehicle into orbit, but funding was stopped and the project cancelled. At around the same time, the HOTOL tried to use precooled jet engine technology, but failed to show significant advantages over rocket technology.

DC-X技術

主條目：McDonnell Douglas DC-X

The maiden flight of the DC-X

The DC-X, short for Delta Clipper Experimental, was an uncrewed one-third scale vertical takeoff and landing demonstrator for a proposed SSTO. It is one of only a few prototype SSTO vehicles ever built. Several other prototypes were intended, including the DC-X2 (a half-scale prototype) and the DC-Y, a full-scale vehicle which would be capable of single stage insertion into orbit. Neither of these were built, but the project was taken over by NASA in 1995, and they built the DC-XA, an upgraded one-third scale prototype. This vehicle was lost when it landed with only three of its four landing pads deployed, which caused it to tip over on its side and explode. The project has not been continued since.

Roton

主條目：Rotary Rocket

From 1999 to 2001 Rotary Rocket attempted to build a SSTO vehicle called the Roton. It received a large amount of media attention and a working sub-scale prototype was completed, but the design was largely impractical.

方法

There have been various approaches to SSTO, including pure rockets that are launched and land vertically, air-breathing scramjet-powered vehicles that are launched and land horizontally, nuclear-powered vehicles, and even jet-engine-powered vehicles that can fly into orbit and return landing like an airliner, completely intact.

For rocket-powered SSTO, the main challenge is achieving a high enough mass-ratio to carry sufficient propellant to achieve orbit, plus a meaningful payload weight. One possibility is to give the rocket an initial speed with a space gun, as planned in the Quicklaunch project.

For air-breathing SSTO, the main challenge is system complexity and associated research and development costs, material science, and construction techniques necessary for surviving sustained high-speed flight within the atmosphere, and achieving a high enough mass-ratio to carry sufficient propellant to achieve orbit, plus a meaningful payload weight. Air-breathing designs typically fly at supersonic or hypersonic speeds, and usually include a rocket engine for the final burn for orbit.

Whether rocket-powered or air-breathing, a reusable vehicle must be rugged enough to survive multiple round trips into space without adding excessive weight or maintenance. In addition a reusable vehicle must be able to reenter without damage, and land safely.

While single-stage rockets were once thought to be beyond reach, advances in materials technology and construction techniques have shown them to be possible. For example, calculations show that the Titan II first stage, launched on its own, would have a 25-to-1 ratio of fuel to vehicle hardware. It has a sufficiently efficient engine to achieve orbit, but without carrying much payload.

Dense versus hydrogen fuels

Hydrogen might seem the obvious fuel for SSTO vehicles. When burned with oxygen, hydrogen gives the highest specific impulse of any commonly used fuel: around 450 seconds, compared with up to 350 seconds for kerosene.

Hydrogen has the following advantages:

• Hydrogen has nearly 30% higher specific impulse (about 450 seconds vs. 350 seconds) than most dense fuels.
• Hydrogen is an excellent coolant.
• The gross mass of hydrogen stages is lower than dense-fuelled stages for the same payload.
• Hydrogen is environmentally friendly.

However, hydrogen also has these disadvantages:

• Very low density (about 1⁄7 of the density of kerosene) – requiring a very large tank
• Deeply cryogenic – must be stored at very low temperatures and thus needs heavy insulation
• Escapes very easily from the smallest gap
• Wide combustible range – easily ignited and burns with a dangerously invisible flame
• Tends to condense oxygen which can cause flammability problems
• Has a large coefficient of expansion for even small heat leaks.

These issues can be dealt with, but at extra cost.

While kerosene tanks can be 1% of the weight of their contents, hydrogen tanks often must weigh 10% of their contents. This is because of both the low density and the additional insulation required to minimize boiloff (a problem which does not occur with kerosene and many other fuels). The low density of hydrogen further affects the design of the rest of the vehicle: pumps and pipework need to be much larger in order to pump the fuel to the engine. The end result is the thrust/weight ratio of hydrogen-fueled engines is 30–50% lower than comparable engines using denser fuels.

This inefficiency indirectly affects gravity losses as well; the vehicle has to hold itself up on rocket power until it reaches orbit. The lower excess thrust of the hydrogen engines due to the lower thrust/weight ratio means that the vehicle must ascend more steeply, and so less thrust acts horizontally. Less horizontal thrust results in taking longer to reach orbit, and gravity losses are increased by at least 300米每秒（1,100公里每小時；670英里每小時）. While not appearing large, the mass ratio to delta-v curve is very steep to reach orbit in a single stage, and this makes a 10% difference to the mass ratio on top of the tankage and pump savings.

The overall effect is that there is surprisingly little difference in overall performance between SSTOs that use hydrogen and those that use denser fuels, except that hydrogen vehicles may be rather more expensive to develop and buy. Careful studies have shown that some dense fuels (for example liquid propane) exceed the performance of hydrogen fuel when used in an SSTO launch vehicle by 10% for the same dry weight.

In the 1960s Philip Bono investigated single-stage, VTVL tripropellant rockets, and showed that it could improve payload size by around 30%.

Operational experience with the DC-X experimental rocket has caused a number of SSTO advocates to reconsider hydrogen as a satisfactory fuel. The late Max Hunter, while employing hydrogen fuel in the DC-X, often said that he thought the first successful orbital SSTO would more likely be fueled by propane.

單台發動機應對所有高度

Some SSTO concepts use the same engine for all altitudes, which is a problem for traditional engines with a bell-shaped nozzle. Depending on the atmospheric pressure, different bell shapes are optimal. Engines operating in the lower atmosphere have shorter bells than those designed to work in vacuum. Having a bell that is only optimal at a single altitude lowers the overall engine efficiency.

One possible solution would be to use an aerospike engine, which can be effective in a wide range of ambient pressures. In fact, a linear aerospike engine was to be used in the X-33 design.

Other solutions involve using multiple engines and other altitude adapting designs such as double-mu bells or extensible bell sections.

Still, at very high altitudes, the extremely large engine bells tend to expand the exhaust gases down to near vacuum pressures. As a result, these engine bells are counterproductive due to their excess weight. Some SSTO concepts use very high pressure engines which permit high ratios to be used from ground level. This gives good performance, negating the need for more complex solutions.

Airbreathing SSTO

Skylon spaceplane

Some designs for SSTO attempt to use airbreathing jet engines that collect oxidizer and reaction mass from the atmosphere to reduce the take-off weight of the vehicle.

Some of the issues with this approach are:

• No known air breathing engine is capable of operating at orbital speed within the atmosphere (for example hydrogen fueled scramjets seem to have a top speed of about Mach 17). This means that rockets must be used for the final orbital insertion.
• Rocket thrust needs the orbital mass to be as small as possible to minimize propellant weight.
• The thrust-to-weight ratio of rockets that rely on on-board oxygen increases dramatically as fuel is expended, because the oxidizer fuel tank has about 1% of the mass as the oxidizer it carries, whereas air-breathing engines traditionally have a poor thrust/weight ratio which is relatively fixed during the air-breathing ascent.
• Very high speeds in the atmosphere necessitate very heavy thermal protection systems, which makes reaching orbit even harder.
• While at lower speeds, air-breathing engines are very efficient, but the efficiency (Isp) and thrust levels of air-breathing jet engines drop considerably at high speed (above Mach 5–10 depending on the engine) and begin to approach that of rocket engines or worse.
• Lift to drag ratios of vehicles at hypersonic speeds are poor, however the effective lift to drag ratios of rocket vehicles at high g is not dissimilar.

Thus with for example scramjet designs (e.g. X-43) the mass budgets do not seem to close for orbital launch.

Similar issues occur with single-stage vehicles attempting to carry conventional jet engines to orbit—the weight of the jet engines is not compensated sufficiently by the reduction in propellant.

On the other hand, LACE-like precooled airbreathing designs such as the Skylon spaceplane (and ATREX) which transition to rocket thrust at rather lower speeds (Mach 5.5) do seem to give, on paper at least, an improved orbital mass fraction over pure rockets (even multistage rockets) sufficiently to hold out the possibility of full reusability with better payload fraction.

It is important to note that mass fraction is an important concept in the engineering of a rocket. However, mass fraction may have little to do with the costs of a rocket, as the costs of fuel are very small when compared to the costs of the engineering program as a whole. As a result, a cheap rocket with a poor mass fraction may be able to deliver more payload to orbit with a given amount of money than a more complicated, more efficient rocket.

Launch assists

Many vehicles are only narrowly suborbital, so practically anything that gives a relatively small delta-v increase can be helpful, and outside assistance for a vehicle is therefore desirable.

Proposed launch assists include:

• sled launch (rail, maglev including Bantam, MagLifter, and StarTram, etc.)
• air launch or aircraft tow
• in-flight fueling
• Lofstrom launch loop/space fountains

And on-orbit resources such as:

• Space tether
• tugs

核推進

主條目：Nuclear propulsion

Due to weight issues such as shielding, many nuclear propulsion systems are unable to lift their own weight, and hence are unsuitable for launching to orbit. However some designs such as the Orion project and some nuclear thermal designs do have a thrust to weight ratio in excess of 1, enabling them to lift off. Clearly one of the main issues with nuclear propulsion would be safety, both during a launch for the passengers, but also in case of a failure during launch. No current program is attempting nuclear propulsion from Earth's surface.

Beam-powered propulsion

主條目：Beam-powered propulsion

Because they can be more energetic than the potential energy that chemical fuel allows for, some laser or microwave powered rocket concepts have the potential to launch vehicles into orbit, single stage. In practice, this area is not possible with current technology.

單級入軌的設計難題

The design space constraints of SSTO vehicles were described by rocket design engineer Robert Truax:

Using similar technologies (i.e., the same propellants and structural fraction), a two-stage-to-orbit vehicle will always have a better payload-to-weight ratio than a single stage designed for the same mission, in most cases, a very much better [payload-to-weight ratio]. Only when the structural factor approaches zero [very little vehicle structure weight] does the payload/weight ratio of a single-stage rocket approach that of a two-stage. A slight miscalculation and the single-stage rocket winds up with no payload. To get any at all, technology needs to be stretched to the limit. Squeezing out the last drop of specific impulse, and shaving off the last pound, costs money and/or reduces reliability.

The Tsiolkovsky rocket equation expresses the maximum change in velocity any single rocket stage can achieve:

$\Delta v=I_{\text{sp}}\cdot g_{0}\ln(MR)$

where:

$\Delta v$ (delta-v) is the maximum change of velocity of the vehicle,

$I_{\text{sp}}$ is the propellant specific impulse,

$g_{0}$ is the standard gravity,

$MR$ is the vehicle mass ratio,

$\ln$ refers to the natural logarithm function.

The mass ratio of a vehicle is defined as a ratio the initial vehicle mass when fully loaded with propellants $\left(m_{i}\right)$ to the final vehicle mass $\left(m_{f}\right)$ after the burn:

$MR={\frac {m_{i}}{m_{f}}}={\frac {m_{p}+m_{s}+m_{\text{pl}}}{m_{s}+m_{\text{pl}}}}$

where:

$m_{i}$ is the initial vehicle mass or the gross liftoff weight $\left(GLOW\right)$,

$m_{f}$ is the final vehicle mass after the burn,

$m_{s}$ is the structural mass of vehicle,

$m_{p}$ is the propellant mass,

$m_{\text{pl}}$ is the payload mass.

The propellant mass fraction ($\zeta$) of a vehicle can be expressed solely as a function of the mass ratio:

$\zeta ={\frac {m_{p}}{m_{i}}}={\frac {m_{i}-m_{f}}{m_{i}}}=1-{\frac {m_{f}}{m_{i}}}=1-{\frac {1}{MR}}={\frac {MR-1}{MR}}$

The structural coefficient ($\lambda$) is a critical parameter in SSTO vehicle design. Structural efficiency of a vehicle is maximized as the structural coefficient approaches zero. The structural coefficient is defined as:

Comparison of growth factor sensitivity for Single-Stage-to-Orbit (SSTO) and restricted stage Two-Stage-to-Orbit (TSTO) vehicles. Based on a LEO mission of Delta v = 9.1 km/s and payload mass = 4500 kg for range of propellant Isp.

$\lambda ={\frac {m_{s}}{m_{p}+m_{s}}}={\frac {m_{s}}{m_{i}-m_{\text{pl}}}}={\frac {\frac {m_{s}}{m_{i}}}{1-{\frac {m_{\text{pl}}}{m_{i}}}}}$

The overall structural mass fraction $\left({\frac {m_{s}}{m_{i}}}\right)$ can be expressed in terms of the structural coefficient:

${\frac {m_{s}}{m_{i}}}=\lambda \left(1-{\frac {m_{\text{pl}}}{m_{i}}}\right)$

An additional expression for the overall structural mass fraction can be found by noting that the payload mass fraction $\left({\frac {m_{\text{pl}}}{m_{i}}}\right)$, propellant mass fraction and structural mass fraction sum to one:

$1={\frac {m_{\text{pl}}}{m_{i}}}+{\frac {m_{p}}{m_{i}}}+{\frac {m_{s}}{m_{i}}}={\frac {m_{\text{pl}}}{m_{i}}}+\zeta +{\frac {m_{s}}{m_{i}}}$

${\frac {m_{s}}{m_{i}}}=1-\zeta -{\frac {m_{\text{pl}}}{m_{i}}}$

Equating the expressions for structural mass fraction and solving for the initial vehicle mass yields:

$m_{i}=GLOW={\frac {m_{\text{pl}}}{1-\left({\frac {\zeta }{1-\lambda }}\right)}}$

This expression shows how the size of a SSTO vehicle is dependent on its structural efficiency. Given a mission profile $\left(\Delta v,m_{\text{pl}}\right)$ and propellant type $\left(I_{\text{sp}}\right)$, the size of a vehicle increases with an increasing structural coefficient. This growth factor sensitivity is shown parametrically for both SSTO and two-stage-to-orbit (TSTO) vehicles for a standard LEO mission. The curves vertically asymptote at the maximum structural coefficient limit where mission criteria can no longer be met:

$\lambda _{\text{max}}=1-\zeta ={\frac {1}{MR}}$

In comparison to a non-optimized TSTO vehicle using restricted staging, a SSTO rocket launching an identical payload mass and using the same propellants will always require a substantially smaller structural coefficient to achieve the same delta-v. Given that current materials technology places a lower limit of approximately 0.1 on the smallest structural coefficients attainable, reusable SSTO vehicles are typically an impractical choice even when using the highest performance propellants available.

案例

It is easier to achieve SSTO from a body with lower gravitational pull than Earth, such as the Moon or Mars. The Apollo Lunar Module ascended from the lunar surface to lunar orbit in a single stage.

A detailed study into SSTO vehicles was prepared by Chrysler Corporation's Space Division in 1970–1971 under NASA contract NAS8-26341. Their proposal (Shuttle SERV) was an enormous vehicle with more than 50,000公斤（110,000英磅） of payload, utilizing jet engines for (vertical) landing. While the technical problems seemed to be solvable, the USAF required a winged design that led to the Shuttle as we know it today.

The uncrewed DC-X technology demonstrator, originally developed by McDonnell Douglas for the Strategic Defense Initiative (SDI) program office, was an attempt to build a vehicle that could lead to an SSTO vehicle. The one-third-size test craft was operated and maintained by a small team of three people based out of a trailer, and the craft was once relaunched less than 24 hours after landing. Although the test program was not without mishap (including a minor explosion), the DC-X demonstrated that the maintenance aspects of the concept were sound. That project was cancelled when it landed with three of four legs deployed, tipped over, and exploded on the fourth flight after transferring management from the Strategic Defense Initiative Organization to NASA.

The Aquarius Launch Vehicle was designed to bring bulk materials to orbit as cheaply as possible.

當前開發

Current and previous SSTO projects include the Japanese Kankoh-maru project, ARCA Haas 2C, and the Indian Avatar spaceplane.

Skylon

主條目：Reaction Engines Skylon

The British Government partnered with the ESA in 2010 to promote a single-stage to orbit spaceplane concept called Skylon. This design was pioneered by Reaction Engines Limited (REL), a company founded by Alan Bond after HOTOL was canceled. The Skylon spaceplane has been positively received by the British government, and the British Interplanetary Society. Following a successful propulsion system test that was audited by ESA's propulsion division in mid-2012, REL announced that it would begin a three-and-a-half-year project to develop and build a test jig of the Sabre engine to prove the engines performance across its air-breathing and rocket modes. In November 2012, it was announced that a key test of the engine precooler had been successfully completed, and that ESA had verified the precooler's design. The project's development is now allowed to advance to its next phase, which involves the construction and testing of a full-scale prototype engine.

廉價空間飛行的其他方法

Many studies have shown that regardless of selected technology, the most effective cost reduction technique is economies of scale. Merely launching a large total number reduces the manufacturing costs per vehicle, similar to how the mass production of automobiles brought about great increases in affordability.

Using this concept, some aerospace analysts believe the way to lower launch costs is the exact opposite of SSTO. Whereas reusable SSTOs would reduce per launch costs by making a reusable high-tech vehicle that launches frequently with low maintenance, the "mass production" approach views the technical advances as a source of the cost problem in the first place. By simply building and launching large quantities of rockets, and hence launching a large volume of payload, costs can be brought down. This approach was attempted in the late 1970s, early 1980s in West Germany with the Democratic Republic of the Congo-based OTRAG rocket.

This is somewhat similar to the approach some previous systems have taken, using simple engine systems with "low-tech" fuels, as the Russian and Chinese space programs still do.

An alternative to scale is to make the discarded stages practically reusable: this is the goal of the SpaceX reusable launch system development program and their Falcon 9, Falcon Heavy, and Starship. A similar approach is being pursued by Blue Origin, using New Glenn.

參見

• 氣尖引擎
• Bristol Spaceplanes
• British Aerospace HOTOL
• Kankoh-maru
• 發射環
• X-33試驗機
• Propellant mass fraction
• X-43試驗機
• Orbital ring
• Rockwell X-30
• Roton
• 超音速燃燒衝壓發動機
• 空間電梯
• 航天器推進
• 三級入軌
• 二級入軌
• 多級火箭
• 冒險之星
• XS-1_(太空飛機)

進一步閱讀

• Andrew J. Butrica: Single Stage to Orbit - Politics, Space Technology, and the Quest for Reusable Rocketry. The Johns Hopkins University Press, Baltimore 2004, ISBN 9780801873386.

外部連結

• A Single-Stage-to-Orbit Thought Experiment （頁面存檔備份，存於互聯網檔案館）
• Why are launch costs so high?, an analysis of space launch costs, with a section critiquing SSTO
• The Cold Equations Of Spaceflight （頁面存檔備份，存於互聯網檔案館） A critique of SSTO by Jeffrey F. Bell.
• Burnout Velocity Vb of a Single 1-Stage Rocket（頁面存檔備份，存於互聯網檔案館）